Author Topic: The no-mod 550 cord mod for gas mask bags!  (Read 2531 times)

0 Members and 1 Guest are viewing this topic.

Offline PetrifiedWood

  • Friction Fire Fellowship
  • Administrator
  • Belt Grinder
  • ******
  • Posts: 11256
The no-mod 550 cord mod for gas mask bags!
« on: August 10, 2012, 01:07:06 AM »
Well after giving this some thought, and then some more thought, I finally figured out a way to rig the gas mask bags I got from Wilderbeast for vertical carry instead of horizontal, with absolutely zero permanent modifications to the bag itself. This is so simple to do I can't believe it took me this long to figure it out! :D

Anyhow, here goes...

First you need one of the gas mask bags, and a piece of 550 cord about 30" long.

Take the long shoulder strap out of the pouch on the side of the bag, the strap with the dee ring on the end. Feed this strap up through the upper left webbing loop that has the snap hook. This will keep the bag from flipping over. The lower snap hook can be tucked into the velcro pouch the shoulder strap is stored in.


Next, you will fold the 550 cord in half and tie a figure 8 knot in it to form a small loop on the end. This will leave two long strands hanging below the loop. Use a girth hitch to attach this loop to the dee ring on the end of the shoulder strap. Here you can see the cord tied to the dee ring and laying inside the pouch. Pass the ends of the cord through the drain holes at the bottom.


Next find the cord ends on the outside of the pouch and tie them together. I used a rewoven figure 8 knot for this.



Finally, load the bag with your gear and close the flap, letting the 550 cord poke out the right side of the flap. Here's what it looks like finished. The entire thing takes 5 minutes to do and the bag can be restored to its original condition just as quickly.



If you try it, let me know how you like it. Thanks for looking! :)


« Last Edit: August 11, 2012, 02:40:06 PM by PetrifiedWood »

Offline MATT CHAOS

  • Friction Fire Fellowship
  • Friction Fire Fellowship
  • Water Stone
  • ***
  • Posts: 3856
  • M.E.S.H. Knives
Re: The no-mod 550 cord mod for gas mask bags!
« Reply #1 on: August 10, 2012, 06:44:39 AM »
I am going to try this.  Thanks for the post!
 :)
Jontok Bushy Approved    Member#28   
1st Aid/CPR/AED Wilderness 1st Aid Instructor

Offline MATT CHAOS

  • Friction Fire Fellowship
  • Friction Fire Fellowship
  • Water Stone
  • ***
  • Posts: 3856
  • M.E.S.H. Knives
Re: The no-mod 550 cord mod for gas mask bags!
« Reply #2 on: August 10, 2012, 11:26:25 AM »
It works great!  Thanks for the info!
 :thumbsup:
Jontok Bushy Approved    Member#28   
1st Aid/CPR/AED Wilderness 1st Aid Instructor

Offline PetrifiedWood

  • Friction Fire Fellowship
  • Administrator
  • Belt Grinder
  • ******
  • Posts: 11256
Re: The no-mod 550 cord mod for gas mask bags!
« Reply #3 on: August 10, 2012, 03:37:00 PM »
Thanks for the feedback, Matt. :)

I'm still hoping to get a few minutes to make a video for this and get some better pictures...

Offline PetrifiedWood

  • Friction Fire Fellowship
  • Administrator
  • Belt Grinder
  • ******
  • Posts: 11256
Re: The no-mod 550 cord mod for gas mask bags!
« Reply #4 on: August 11, 2012, 02:40:26 PM »
Ok, edited the original post with better pictures.

Offline Wilderbeast

  • Vendor
  • Water Stone
  • ***
  • Posts: 4944
  • Member #007
    • Military Spec Surplus
Re: The no-mod 550 cord mod for gas mask bags!
« Reply #5 on: August 11, 2012, 07:59:41 PM »
Good idea PW.

Thanks for the pictures.
Upon this a question arises: whether it be better to be loved than feared or feared than loved? One should wish to be both, but, because it is difficult to unite them in one person, it is much safer to be feared than loved.

Offline RBM

  • Friction Fire Fellowship
  • Whetstone +
  • **
  • Posts: 501
  • Philippians 4:13
    • YouTube Channel
Re: The no-mod 550 cord mod for gas mask bags!
« Reply #6 on: August 23, 2012, 06:12:29 PM »
Works great. Thanks for the tweak, PW.
Robert