Author Topic: J.D. 1050 my new helper...  (Read 18795 times)

0 Members and 1 Guest are viewing this topic.

Offline xj35s

  • Water Stone
  • ***
  • Posts: 2168
  • If I go missing, carladerby at gmail for info.
Re: J.D. 1050 my new helper...
« Reply #50 on: April 06, 2020, 07:11:11 PM »
unfortunately it's a lot of sand and some clay here and there. lots of fertilizer going in.
pessimist complain about the wind. optimist expect the wind to change. realist adjusts the sails.

Offline wsdstan

  • Supporting Member
  • Belt Grinder
  • *****
  • Posts: 10054
Re: J.D. 1050 my new helper...
« Reply #51 on: April 06, 2020, 10:51:22 PM »
Thanks.  It is that way here in places.  My neighbors field next to mine has about 18" of old river bottom dirt on top of five feet or more of pure sand.  We put a irrigation line in a few years back and it was like trying to trence snow. 
A man who carries a cat by the tail learns  something he can learn in no other way. 
(Mark Twain)

Offline xj35s

  • Water Stone
  • ***
  • Posts: 2168
  • If I go missing, carladerby at gmail for info.
Re: J.D. 1050 my new helper...
« Reply #52 on: April 24, 2020, 05:42:49 AM »
Okay, I'm bragging again. I'm not real proud though. Not quite how I wanted it. I'm hoping it will kind of draw the material into the bucket as it closes.
I should have added the toothbar before finishing this grapple. I don't know if it'll hit a tooth or land between them. No matter really. I have a hydraulic splitter valve coming. I'll be able to operate the bucket or the grapple using the same lever by a toggle switch. 2 lines in 4 lines out, for two seperate two way cylinders. I hope that makes sense?
This entire contraption comes off by removing 4 bolts from the top of the bucket. My intension is to build some attachments that will be able to bolt onto the sides of the thumb. I'll drill two holes on each side and weld a nut to the inside. Then I can build a rake, toothed top bar, or tiny clamping back blade.
Just killing time since I'm not working and can't go anywhere.





pessimist complain about the wind. optimist expect the wind to change. realist adjusts the sails.

Offline wsdstan

  • Supporting Member
  • Belt Grinder
  • *****
  • Posts: 10054
Re: J.D. 1050 my new helper...
« Reply #53 on: April 24, 2020, 07:34:34 AM »
The overall design looks like it will push material like brush and old scattered hay left from feeding into the bucket.  It also should hold small tree limbs longer than the width of the bucket so they can be picked up and moved.

I don't mean this in a criticizing way but I think the vertical bars and the pivot points are potentially going to wear quickly or bend if too much weight or pressure is applied.  For light loads it should work well.  I have a lot of debris stacked up along our creek in places and this would make short work of picking it up and carrying it to a burn pile.

It looks like a good deal to me and especially so since you built it with materials on hand.  Good job.
A man who carries a cat by the tail learns  something he can learn in no other way. 
(Mark Twain)

Offline xj35s

  • Water Stone
  • ***
  • Posts: 2168
  • If I go missing, carladerby at gmail for info.
Re: J.D. 1050 my new helper...
« Reply #54 on: April 24, 2020, 08:56:59 AM »
I agree. I have two piles of slab wood to move I hope it lasts long enough for that. The square tube across the top is 14 gauge, the down bars are 4" x 1/4". Yes I should have built a double shear at the pivot. I need to incorporate a bump stop and hope to use it as a second side of the pivot. Right now it can go past center and flip back towards the tractor. The ram closes fully but allows the grapple to open enough to go past the center point.
I hope this small ram isn't ridiculously fast. I have a flow limiter If I need it though.
pessimist complain about the wind. optimist expect the wind to change. realist adjusts the sails.

Offline xj35s

  • Water Stone
  • ***
  • Posts: 2168
  • If I go missing, carladerby at gmail for info.
Re: J.D. 1050 my new helper...
« Reply #55 on: May 02, 2020, 05:54:03 PM »
The top pipe ripped to pieces where the ram mount was welded on and I bent the angle iron top of the thumb. I got some very heavy rectangle tube wth a 1/4" wall from my neighbor. I bartered for it. I am clearing a few hundred sumac trees from his side hill. In the process I bent the teeth and broke one off completely. I wish I could find it too I don't want to pop a tire. It did a killer job getting them out of the ground though. I should have welded some 1/2" square to the bottom of the teeth behind them along the bottom of the bucket. It would have helped hold them straight. I will now...
pessimist complain about the wind. optimist expect the wind to change. realist adjusts the sails.

Offline wsdstan

  • Supporting Member
  • Belt Grinder
  • *****
  • Posts: 10054
Re: J.D. 1050 my new helper...
« Reply #56 on: May 02, 2020, 07:40:34 PM »
Well it worked well till it broke and that is progress.  Next one will be better.  Hope you find the broken tooth, they are probably hell on tires, just like deer antlers.
A man who carries a cat by the tail learns  something he can learn in no other way. 
(Mark Twain)

Offline wolfy

  • Supporting Member
  • Belt Grinder
  • *****
  • Posts: 19114
  • "You want a toe? I can get you a toe." -Sobchak
Re: J.D. 1050 my new helper...
« Reply #57 on: May 03, 2020, 09:17:25 AM »
.....and cultivator shovels.  >:(
The only chance you got at a education is listenin' to me talk!
Augustus McCrae.....Texas Ranger      Lonesome Dove, TX