Pages: [1]   Go Down

Author Topic: spindle sander problems  (Read 2724 times)

0 Members and 1 Guest are viewing this topic.

Offline hayshaker

  • Whetstone +
  • **
  • Posts: 904
spindle sander problems
« on: August 05, 2018, 06:07:01 PM »
I have a spindle sander the one that goes up&down, yeah anyhow
how does one keep the sandingtube from continually slipping off
i stopped using for some time because of that. and i would like to start using it again,
help needed
Logged

Offline madmax

  • Diamond Stone
  • ****
  • Posts: 9736
  • The Phoenix
Re: spindle sander problems
« Reply #1 on: August 06, 2018, 11:37:04 AM »
I have been pondering this for awhile and all I can think of is dirty comments.
Logged
"Life should not be a journey to the grave with the intention of arriving pretty with a well preserved body, but rather to skid in sideways in a cloud of smoke, thouroughly used up, totally worn out, and loudly proclaiming, Wow! What a ride!" 
Hunter S, Thompson

Offline wsdstan

  • Supporting Member
  • Diamond Stone
  • ****
  • Posts: 9313
Re: spindle sander problems
« Reply #2 on: August 06, 2018, 11:50:40 AM »
Oh, you watched one going up and down didn't you?
Logged
A man who carries a cat by the tail learns  something he can learn in no other way. 
(Mark Twain)

Offline wsdstan

  • Supporting Member
  • Diamond Stone
  • ****
  • Posts: 9313
Re: spindle sander problems
« Reply #3 on: August 06, 2018, 12:05:11 PM »
Mike if the paper tubes are coming off you may have a problem with the rubber tube or you bought some sleeves that are not the correct size by just a little bit.  Clean the tubes of all debris and see how tight the fit is when you slide the sanding tube on.

What brand is yours?
Logged
A man who carries a cat by the tail learns  something he can learn in no other way. 
(Mark Twain)

Offline madmax

  • Diamond Stone
  • ****
  • Posts: 9736
  • The Phoenix
Re: spindle sander problems
« Reply #4 on: August 06, 2018, 01:00:39 PM »
Quote from: wsdstan on August 06, 2018, 11:50:40 AM
Oh, you watched one going up and down didn't you?

I take offense at your accusation of my autoeroticism?. especially with sandpaper.
Logged
"Life should not be a journey to the grave with the intention of arriving pretty with a well preserved body, but rather to skid in sideways in a cloud of smoke, thouroughly used up, totally worn out, and loudly proclaiming, Wow! What a ride!" 
Hunter S, Thompson

Offline madmax

  • Diamond Stone
  • ****
  • Posts: 9736
  • The Phoenix
Re: spindle sander problems
« Reply #5 on: August 06, 2018, 01:04:01 PM »
ok ok.  I'll take my meds.
Logged
"Life should not be a journey to the grave with the intention of arriving pretty with a well preserved body, but rather to skid in sideways in a cloud of smoke, thouroughly used up, totally worn out, and loudly proclaiming, Wow! What a ride!" 
Hunter S, Thompson

Offline crashdive123

  • Vendor
  • Water Stone
  • ***
  • Posts: 4162
Re: spindle sander problems
« Reply #6 on: August 06, 2018, 01:34:16 PM »
You should have a washer and screw at the top of each spindle.  By tightening the screw, the washer compresses the rubber on the spindle which in turn holds the sanding tube in place.
Logged

Offline madmax

  • Diamond Stone
  • ****
  • Posts: 9736
  • The Phoenix
Re: spindle sander problems
« Reply #7 on: August 06, 2018, 02:32:50 PM »
Stop please.  it's excruciating.
Logged
"Life should not be a journey to the grave with the intention of arriving pretty with a well preserved body, but rather to skid in sideways in a cloud of smoke, thouroughly used up, totally worn out, and loudly proclaiming, Wow! What a ride!" 
Hunter S, Thompson

Offline wsdstan

  • Supporting Member
  • Diamond Stone
  • ****
  • Posts: 9313
Re: spindle sander problems
« Reply #8 on: August 06, 2018, 02:57:23 PM »
Sandpaper can be extremely excruciating. 
Logged
A man who carries a cat by the tail learns  something he can learn in no other way. 
(Mark Twain)

Offline hayshaker

  • Whetstone +
  • **
  • Posts: 904
Re: spindle sander problems
« Reply #9 on: August 06, 2018, 04:30:49 PM »
thanks everyone and crash yer right all it was to tighten up the top nut.
the sander is a performax osscilating spinle sander.
Logged

Offline papadan

  • Mill File
  • *
  • Posts: 13
  • Just waitin for my ride!
Re: spindle sander problems
« Reply #10 on: August 19, 2018, 08:45:48 PM »
We have to revive this one. Oscillating up and down you say?
Logged
Just piddlin round, waitin on my ride!

Offline Spyder1958

  • Water Stone
  • ***
  • Posts: 2618
  • Kracaneuner Tribe
Re: spindle sander problems
« Reply #11 on: August 20, 2018, 06:18:16 PM »
Don't get Tony started, LOL
Logged
You are free to choose but you are not free from the consequences of your choice.
Zig Ziglar

Offline hayshaker

  • Whetstone +
  • **
  • Posts: 904
Re: spindle sander problems
« Reply #12 on: August 28, 2018, 05:35:38 AM »
i heard about this one bar down in cow key channel by keywest,fla,
oh wait i forgot this is a family fourm nevermind about the rattan basket chair
Logged

Offline papadan

  • Mill File
  • *
  • Posts: 13
  • Just waitin for my ride!
Re: spindle sander problems
« Reply #13 on: August 28, 2018, 02:06:11 PM »
Send me a PM concerning that chair.;-)
Logged
Just piddlin round, waitin on my ride!

Offline madmax

  • Diamond Stone
  • ****
  • Posts: 9736
  • The Phoenix
Re: spindle sander problems
« Reply #14 on: August 28, 2018, 03:07:05 PM »
Don't ask him papadan.  He'll just get revved up.
Logged
"Life should not be a journey to the grave with the intention of arriving pretty with a well preserved body, but rather to skid in sideways in a cloud of smoke, thouroughly used up, totally worn out, and loudly proclaiming, Wow! What a ride!" 
Hunter S, Thompson

Offline papadan

  • Mill File
  • *
  • Posts: 13
  • Just waitin for my ride!
Re: spindle sander problems
« Reply #15 on: August 28, 2018, 09:37:23 PM »
Quote from: madmax on August 28, 2018, 03:07:05 PM
Don't ask him papadan.  He'll just get revved up.
Here's hoping!
Logged
Just piddlin round, waitin on my ride!
Pages: [1]   Go Up